FAST ComTec: BNC Model PB-4

BNC Model PB-4, Precision Pulse Generator

Features

Flat Top or Tail Pulse
Repetition Rate 250 kHz
Rise and Fall Times Independently Adjustable
Output Impedance 50 ohms
Temperature Coefficient +/-5 ppm/^oC
Integral Linearity +/-50 ppm
Amplitude shift less than 0.03% at 50% duty factor

Description

The Model PB-4 provides either a tail or flat top pulse with an integral linearity of +/-50 ppm and an amplitude temperature coefficient of +/-5 ppm/^oC. The Model PB-4 is designed to test stability, linearity, and resolution of nuclear instruments employed in high resolution spectroscopy. It also offers the high count rates that are so important in many of these tests.

Applications

Use as a reference peak for spectrum stabilization
Testing count rate effects up to 250 kHz
Measuring differential and integral linearity of pulse height analyzers
Measuring noise from preamplifiers and amplifiers

Description

The Model PB-4 employs a solid state chopper (no mercury relays) which samples either an internal DC reference voltage or an externally supplied reference source. The output of the chopper is connected to a high gain, fast slewrate operational amplifier to provide the possibility of driving heavy loads. The internal DC reference source, the chopper and the operational amplifier are all enclosed in a proportional control oven whose internal temperature changes only 0.01^oC for a 1^oC change in ambient.

Sliding Pulse Operation

A sliding pulse generator provides a pulse train of linearly increasing (or decreasing) pulses to test the differential linearity of multi-channel pulse height analyzers. To obtain a sliding pulse train from the Model PB-4 it is necessary to connect a Berkeley Nucleonics Model LG-1 Ramp Generator to its External Reference input. The solid-state chopper in the Model PB-4 samples the ramp at periodic intervals. The output of the Model PB-4 is then connected to the pulse height analyzer. If the analog-digital converter is linear and the magnetic core storage is functioning correctly, an equal number of counts will be stored in each channel and the display will be a horizontal straight line. However, if the analyzer is non-linear the display may curve up. If the magnetic core storage is defective there may be a notch in the display. The differential linearity of the sliding pulse train is better than +0.1%. The above approach is the fastest, most accurate way of testing a pulse height analyzer.

Specifications

INPUTS and OUTPUTS

External Trigger: 0 to 250 kHz, requires 1 V, positive pulse, with a rise time < 1 ms.

Amplitude: 0.0 to 10.0 V

Trigger Out: 2 V positive pulse, 30 ns rise time, 0.1 us width, 50 ohms output impedance.

External Reference Input: +/-11 V maximum. Input impedance 1 k. Primary function is to connect with an external ramp generator to provide a sliding pulse train.

GENERAL

Amplitude Characteristics:
Stability: +/-5 ppm/^oC of full scale or 20 mV/^oC, whichever is greater. This specification holds for unattenuated output. When attenuation is switched in, the +/-5 ppm/^oC is constant, while 20 mV/^oC is reduced by the attenuation factor.
Integral non-linearity: +/-0.005% (50 ppm).
Differential Non-Linearity: +/-0.03%.
Amplitude Jitter (Resolution): 0.001% rms (10 ppm).
Setability of Pulse Amplitude: 5 ppm.
Line Voltage Coefficient: Less than 0.5 ppm/V

Power Requirements:
+/-24 V at 240 mA

PHYSICAL

Size:
Triple-width AEC NIM module 4.05" wide x 8,70" high in accordance with TID-20893 (Rev. 3).

Weight:
6.5 lbs. net; 9 lbs. Shipping.

CONTROLS

Single Cycle: Front panel push-button provides one output pulse each time the button is pressed.

Rep Rate: 2.5 Hz to 250 kHz, continuously variable

Delay: 0.25 ms to 10 ms. continuously variable. (Delay is time between trigger out and pulse out.)

Tail Pulse:
Rise Time (10%-90%): 0.05 ms to 10 ms, in 8 steps.
Decay Time Constant (100%-37%): 0.5 ms to 1 ms, in 9 steps.
Rise and Decay Time Independently Adjustable for Decay Time/Rise Time >10.

Flat Top Pulse:
Width: 0.5 ms to 25 ms, continuously adjustable.
Pulse Top Droop: less than 0.02% with 10 ms pulse width.
Rise and Decay Time: Same as tail pulse.

Normalize: Fine and coarse front panel trimmers vary output amplitude by 20%.

Polarity: Positive or Negative.

Attenuators: Four toggles with X2, X5, X10, X10 attenuation, 50 ohms impedance.

Overview Nuclear Pulse-Generators