Model THQ-T1DPxx and THQ-T2DPxx, Benchtop High Voltage Power Supplies
Check the product tables for further information!
THQ T1DPxx and T2DPxx: Single and dual channel versions in benchtop case
Model
DP01
DP02
DP03
DP04
DP05
DP06
Output voltage Vo
1kV
2kV
3 kV
4kV
5kV
6kV
Stability ΔVin
< 1 x 10-5 x Vomax
Stability ΔRload
< 5 x 10-5 x Vomax
Ripple and noise
typ. 2 mVp-p max. 7 mVp-p
Temp. coefficient
< 5 x 10-5/K
Remote control
Control and monitor voltage for Vo and Io : 0 to 5 V
INHIBIT
TTL-Level, LOW = active Δ Vo = 0
Polarity
positive or negative, switchable
Protection
overload and shortcircuit, voltage and current limit with trimmer potentiometer
Case
Metal box
Dimension (L/W/H)
(300 with SHV / 310 / 90) mm
Supply voltage
110-240V AC, 50/60 Hz
Configuration Table and Ordering Information
Model
Desciption
Order No.
T1DP01
1 x 1 kV
HVIC01
T1DP02
1 x 2 kV
HVIC02
T1DP03
1 x 3 kV
HVIC03
T1DP04
1 x 4 kV
HVIC04
T1DP05
1 x 5 kV
HVIC05
T1DP06
1 x 6 kV
HVIC06
T2DP11
2 x 1 kV
HVIC11
T2DP22
2 x 2 kV
HVIC22
T2DP33
2 x 3 kV
HVIC33
T2DP44
2 x 4 kV
HVIC44
T2DP55
2 x 5 kV
HVIC55
T2DP66
2 x 6 kV
HVIC66
Features
Single and Dual HV supplies in benchtop case
Low cost desk top HV PS with 1 or 2 channels
LED display 3 1/2 digits for voltage or current, switchable
Equipped with DPS HV modules
Output voltages 1 kV up to 6 kV at max. 12 Watts
Very low EMI
High precision output voltage with very low ripple and noise
Short circuit and overload protected
Continuous setting of HV over full range with 10 turn Helipot or by Analog I/O on 9 pin D Sub connector.
Access to manual polarity switch on DPR module, optionally switchable via TTL signal (up to 3 KV only)
Freely configurable with one or two DPS modules
Description
These robust desk top high voltage power supplies consist of the THQ housing and one or two high voltage modules of the DPS series which have an unsurpassed price/performance ratio. The units are available with one or two high voltage modules. Special versions with any combination of DPR modules can be quoted on request. The output voltage is controlled by a frontpanel potentiometer. For external control and monitoring an analog I/O is also available (set voltage and monitor voltage 0 to 5 V) on a D Sub 9 connector on the rear panel. Hardware settings for voltage and current limits protect the connected devices. Our patented resonance mode principle and the allmetal box guarantees lowest EMI. Output voltage and current can be choosen on a switchable LED-display. The DPS series includes HV power supply modules with output voltages from 1 kV to 6 kV at max. 12W. The polarity switch in the housing of the DPS module enables the user to set the desired polarity.
